NiO-CuO/ZSM-5催化剂对催化裂化烟气的脱硫脱硝性能

采用浸渍法制备了不同NiO和CuO质量分数的NiO-CuO/ZSM-5催化剂，并以CH4为还原剂研究了NiO-CuO/ZSM-5催化剂对催化裂化烟气的脱硫脱硝活性。XRD分析结果表明，NiO质量分数为4%、CuO质量分数为6%的催化剂4%NiO-6%CuO/ZSM-5中的ZSM-5结构完好，CuO和NiO高度分散在ZSM-5骨架中，表明具有较好的催化活性。4%NiO-6%CuO/ZSM-5的脱硫脱硝起活温度均较低，无氧条件下最高NO转化率和SO2转化率分别为94.7%和95.9%，O2体积分数为1.0%时的NO转化率和SO2转化率分别为97.7%和89.0%。     

火电厂SCR烟气脱硝催化剂特性及其应用

SCR工艺是火电厂的主流烟气脱硝技术，催化剂是SCR脱硝工艺的核心。通过对不同型式催化剂特性及其应用的对比分析，得出了蜂窝式催化剂综合性能较优的结论，并对不同烟气条件下的催化剂选择提出了建议.     

A preliminary process design and economic assessment of a catalyst rejuvenation process for waste disposal of refinery spent catalysts

Spent hydroprocessing catalysts from refineries have been classified as hazardous solid waste by the United States Environmental Protection Agency (USEPA), refiners must find a viable but economical solution to solve this serious environmental issue. Catalyst rejuvenation is an attractive option for minimizing the environmental problems associated with spent catalysts. In this study, a preliminary design for such a process and the corresponding economic analysis are performed to assess the proposed catalyst rejuvenation process for metal-fouled spent catalysts generated in residue hydroprocessing units. The scenarios used in the economic assessment are based on three options of process synthesis and two operator modes. It is found that the option of rejuvenating medium and lightly fouled spent catalyst produced by the refinery will be the best solution for refiners, both environmentally and economically.     

Glucose production from hydrolysis of cellulose over a novel silica catalyst under hydrothermal conditions

A novel silica catalyst was synthesized by evaporation-induced self-assembly (EISA) method and tested for the catalytic selective hydrolysis of cellulose to glucose. This silica catalyst exhibited a higher catalytic activity than other oxides prepared by the same method, such as ZrO₂, TiO₂, and Al₂O₃. Using silica as a catalyst, cellulose was selectively hydrolyzed into glucose with a glucose yield as high as 50% under hydrothermal conditions without hydrogen gas. The silica catalyst was characterized by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results of temperature-programmed desorption of ammonia (NH₃-TPD) and textural properties indicated that the synergistic effect between strong acidity and a suitable pore diameter of the silica catalyst may be responsible for its high activity. In addition, the catalyst was recyclable and showed excellent stability during the recycle catalytic runs.     

Effects of WOx modification on the activity, adsorption and redox properties of CeO2 catalyst for NOx reduction with ammonia

A series of WO₃/CeO₂ (WOx/CeO₂) catalysts were synthesized by wet impregnation of ammonium metatungstate on a CeO₂ support. The resulting solid acid catalysts were characterized by X-ray diffraction (XRD), UV-Vis spectroscopy (UV-Vis), Raman spectroscopy (Raman), in-situ Fourier transform infrared spectroscopy (in-situ FT-IR) of ammonia adsorption, NH₃-TPD, H₂ temperature-programmed reduction (H₂-TPR), NH₃/NO oxidation and activity measurements for NOx reduction by NH₃ (NH₃-SCR). The results show that polytungstate (WOx) species are the main species of tungsten oxide on the surface of ceria. The addition of tungsten oxide enhances the Brönsted acidity of ceria catalysts remarkably and decreases the amount of surface oxygen on ceria, with strong interaction between CeO₂ and WOx. As a result, the N₂ selectivity of NH₃ oxidation and NH₃-SCR at high temperatures (> 300℃) is enhanced. Therefore, a wide working temperature window in which NOx conversion exceeds 80% (NOx conversion > 80%) from 200 to 450℃, is achieved over 10 wt.% WOx/CeO₂ catalyst. A tentative model of the NH₃-SCR reaction route on WOx/CeO₂ catalysts is presented.     

锰铈脱硝催化剂的制备及其再生性能研究

采用等体积浸渍法制备了一系列Mn-Ce-Ox复合氧化物脱硝催化剂用于NH3选择性催化还原(NH3-SCR)NO。考察了Mn/Ce摩尔比、焙烧温度、H2O和SO2对Mn-Ce-Ox复合氧化物脱硝催化剂活性的影响及催化剂中毒再生性能。结果表明:当NH3:NO=1:1,空速为5 000 h-1,550℃焙烧制得的Mn/Ce摩尔比为5∶1的Mn-Ce-Ox复合脱硝催化剂活性最佳,活性温度窗口为100~260℃,在此温度区间内催化剂活性大于90%。200℃时,Mn-Ce-Ox复合催化剂活性最高为97.84%;在10%(V/V)H2O蒸汽和300×10-6SO2共存条件下,200℃时,催化剂活性在开始反应2.5 h内迅速下降至53%左右,并在之后的6 h内没有明显变化;中毒催化剂经常温水洗再生处理、质量分数为3%的硝酸溶液再生处理和550℃焙烧2 h再生处理后200℃活性均能恢复到90%以上,其中中毒催化剂经质量分数为3%硝酸处理后活性恢复率最高。     

铁氮掺杂碳纳米管/纤维复合物制备及其催化氧还原的效果

阴极催化剂是影响微生物燃料电池(microbial fuel cell,MFC)性能的关键因素.通过研究制备成本低廉、氧还原反应(ORR)催化活性高的阴极催化剂来替代Pt/C对于实现MFC规模化应用具有重大意义.研究采用化学气相沉淀法,以三聚氰胺作为碳氮前驱物、以黑珍珠2000或乙炔炭黑作为碳源,外加醋酸亚铁作为铁前驱物,合成了两种铁氮掺杂碳纳米管/纤维复合物(FeNCB和FeNCC),作为MFC的阴极催化剂.通过循环伏安法和旋转圆盘-环电极分析FeNCB、FeNCC和Pt/C的ORR催化活性的差异,并用MFC验证其差异.结果表明,FeNCB性能与Pt/C相当,优于FeNCC,其催化路径是通过4电子途径催化氧还原反应;MFC-FeNCB性能略优于MFC-Pt/C,显著优于MFC-FeNCB有助于MFC的扩大化,其最大功率密度为1 212.8mW·m~(-2),开路电压为0.875 V,电池稳定电压为(0.500±0.025)V.用X射线衍射、X射线光电子光谱、拉曼光谱等进一步分析显示,复合物中碳纳米管管径的大小、铁氮掺杂的类型和含量以及氧含量是引起制备的复合物催化氧还原性能差异的原因所在.     

三维有序介孔铈钴铜催化剂的制备及其降解邻二甲苯的机制

以PMMA为模板,通过聚乙二醇(PEG400)和柠檬酸辅助的溶胶凝胶法制备三维有序介孔铈钴铜(3DOM 3C)催化剂,应用BET、SEM、XRD和XPS等对不同煅烧温度的3DOM 3C催化剂进行表征分析,研究了催化剂活性及其影响因素,并利用FT-IR和GC-MS对降解产物进行分析,推测出催化降解邻二甲苯的机理.结果表明,煅烧温度500℃时制备的3DOM 3C催化剂表面具有三维介孔结构,且分散均匀,表面的晶体氧化物最少,存在大量的Cu~(2+)、Ce~(3+)和表面氧,催化剂表面存在更多的固溶体、表面活性位点和氧空位,有利于提高催化活性.在邻二甲苯初始浓度600 ppm、空速16000 h~(-1)、50%O_2条件下,煅烧温度500℃时制备的3DOM 3C催化效果最佳,在260℃时,3DOM 3C催化剂对邻二甲苯的转化率达98%,T_(90)为250℃. 3DOM 3C对邻二甲苯的转化率随着初始浓度、空速和相对湿度的升高而呈下降趋势,随着O_2含量的增加而增加.气流中混入150 ppm的乙酸乙酯能够提高邻二甲苯的转化率,提高其低温催化性能.邻二甲苯催化反应后催化剂表面的O—H、■、C—H和金属—氧键都相应的减少,降解中间产物主要有邻甲基苯甲醛和邻甲基苯甲酸.邻二甲苯降解反应涉及Mars Van Krevelen机理(MVK),先被氧化成邻甲基苯甲醛,再进一步氧化成邻甲基苯甲酸,最终生成CO_2和H_2O.     

硅藻土负载纳米铁对Cd2+的吸附性能与机制研究

为了提高硅藻土(CDt)的吸附能力,采用NaBH_4液相还原二价铁法合成负载纳米铁的硅藻土颗粒(nZVI-CDt),运用扫描电镜(SEM)、傅里叶红外光谱(FTIR)、X射线衍射(XRD)和X射线光电子能谱(XPS)对nZVI-CDt进行表征,采用静态吸附法研究不同吸附条件对CDt和nZVI-CDt吸附Cd~(2+)的影响,并结合等温吸附属性、吸附过程控制步骤以及吸附动力学、热力学属性分析探讨了CDt和nZVI-CDt对Cd~(2+)的吸附机制.结果表明,负载纳米铁后,硅藻土的团聚现象得到改善,分散性更好,表面活性基团向有利于吸附方向发生变化,吸附能力得到显著提升,相对于CDt,nZVI-CDt对Cd~(2+)的吸附量提升了3.9倍;nZVI-CDt对Cd~(2+)的吸附较为迅速,20 min左右就可达到吸附平衡;随着投加量的增加,nZVI-CDt对Cd~(2+)的吸附量呈下降趋势,而初始浓度对Cd~(2+)的吸附影响则正好相反;相对于CDt,溶液初始pH值对nZVI-CDt吸附Cd~(2+)的影响明显减弱;nZVI-CDt对Cd~(2+)的吸附能力受温度影响不大;nZVI-CDt对Cd~(2+)的吸附符合Temkin等温吸附模型和拟二级动力学模型.吸附反应容易进行,且以物理吸附为主,吸附过程控制步骤为发生在微孔内的吸附反应.吸附热力学参数表明CDt和nZVI-CDt对Cd~(2+)的吸附是自发的吸热过程,且系统的无序性增加.     

生物合成施氏矿物作为类芬顿反应催化剂降解甲基橙的研究

应用生物合成施氏矿物作为光助类芬顿反应催化剂促进甲基橙的降解.施氏矿物通过A.f-LX5细胞悬浮液在初始p H值2.5和28℃时氧化Fe SO43d生成,并进行X射线衍射和扫描电子显微镜表征.本研究分析了不同初始p H、H2O2浓度及催化剂装载量对在光助类芬顿反应中甲基橙氧化降解效率的影响.结果表明,生物合成施氏矿物具有较高的催化活性,并且通过羟基自由基机制使甲基橙降解.在近中性、较高Cl-、SO2-4及NO-3浓度条件下,施氏矿物仍然能保持较高催化甲基橙降解的效率.本研究验证了以生物合成施氏矿物作为催化剂的异相光助类芬顿反应是一种处理含甲基橙废水有应用前景的高级氧化技术.